Monday 2 November 2015

November Challenge #1

Welcome to November!!  

Have you ever done a blind scrap?  I will list the items you need, with a set of instructions,  but no photo!  Blind scrapping,  just means you follow steps to create a layout, you can add your own unique twists at any stage as long as the basic recipe is followed.
After a week I will post my layout in the gallery, so as not to spoil it for those that wish to keep it a 'Blind'  challenge...

PHOTO  -
You need 1 12.5 x 17.5 cm landscrape photo (you can also use 2 smaller photo together if you wish, but the over all size needs to be 12.5 x 17.5 cm in a landscape orientation)

SUPPLIES -
1 Base cardstock
4 sheets of pattern paper - or 2 double sided ones
1 extra piece of coordinating PP at least 15 x12cm
2 different alpha - 1 lager and 1 smaller
3D foam or similar
1 circle punch at least 3cm wide ( or hand cut one)
1 journalling pen 
Coordinating ink for the edges of your pp
Distressing tool 
DST

EMBELLISHMENTS - 
3 stars or hearts (no larger than about 3cm)
2 buttons or flairs
packet of coordinating rhinestones or pearls 
Brads or enamal dots (or similar)

STEPS
Distress and ink your cardstock - (refered to as CS in the steps)

Cut your pp into the following sizes
A  25x24 cm
B 20x16cm
C 10 x15cm
D 5.5 x 15cm
Then distress and ink each piece

From the extra piece of  coordinating PP hand rule and cut out 2 arrows,  1 approx 10cm long and 7cm high and another 2.5cm long and 3cm high and 1 heart.....Ink but do not distress arrows.

Place pp A in the middle of the CS
Place pp C hard up against the left hand side of the CS and 13cm down from the top
Place pp D hard up against the left hand side of the CS and 17cm down from the top
Place pp B 9cm down from the top and .5cm from the right hand side of your CS.
Place your photo 10.5cm down from the top of the CS 1.5cm from the right hand side 

Place your large alpha title on the top left hand side of pp A  with your smaller sub-title or jorumalling letters 

Punch or cut a circle from a scrap piece of pp, cut in half or fold over and place it on the top of pp , 5cm from the right hand side, add a flair or button along side of it. (i added a small word on my circle with a rub-one... you could stamp or hand write on it)

Add the heart, just sitting overlaying left hand edge of your photo slightly, and on the bottom half of it.

Add the large arrow on the bottom left hand side of your photo using 3D form, should be sitting under the heart, mine of overlapping a little. 

Add the small arrow on the right hand side along with the 2nd button or flair and add a few rhinestones to make a small grouping

Under the photos and above the arrow, sprinkle with your stars and rhinestones.

Using your ruler and jounalling pen, rule a small boarder around the outside edge of your pp....and anywhere else you would like... On mine I outlined the small arrow and 2 of my stars...

Any questions, message or post on our chat page and I will answer them there :)

Challenge Rules:
  • Create a NEW project layout or canvas for this challenge 
  • Please upload your entry to our gallery (and/or Inlinkz) by 11.55pm 30th Nov to be eligible for the prize. 
  • Have fun and please share with your scrappy friends
International entries are welcome, , however due to international postage cost a Creative Design Spot will be offered along with a little surprise in the post.

Australia residence, this month's prize is a 3 piece Chipboard Pack valued over $10.00.

Enjoy!!

Mystical Team







1 comment:

  1. great challenge.
    i have only done a blind scrap once before. I use to set blind scrap challenges when was on a dt.
    i hope i do a ok job at doing it lol

    ReplyDelete